Electrical, Battery and Solar

Relaxn Heavy-Duty Terminal Studs - M10 Positive Single Provides a neat electrical wiring solution Base made from glass fibre reinforced nylon for strength and durability Max amp per current is determined by wires connected Part Number Pack...

Relaxn Heavy-Duty Terminal Studs - M8 Positive Single Provides a neat electrical wiring solution Base made from glass fibre reinforced nylon for strength and durability Max amp per current is determined by wires connected Part Number Pack...

Deck Switch For Anchor Winches. Heavy-duty deck switch with waterproof deck mounting. Rated at 150 amps continuous. 6 x countersunk mounting holes Part Number Volts Cut Out Diameter Overall Diameter SAW-30200 12v /...

Deck Switch For Anchor Winches - Twin Pack Heavy-duty deck switch with waterproof deck mounting. Rated at 150 amps continuous. 6 x countersunk mounting holes Part NumberVoltsOverall Diameter SAW-30202 12v / 24V 120mm

Circuit Breaker Surface Mount - 60 Amps, IP67 Sealed outer casing making it idea for engine compartments and marine based applications. If a fault is detected the unit with cut power immediately with a unique reset switch. High Amp circuit breaker...

Sealed outer casing making it idea for engine compartments and marine based applications. If a fault is detected the unit with cut power immediately with a unique reset switch. High Amp circuit breaker manual reset. Sealed IP67 for engine...

Sealed outer casing making it idea for engine compartments and marine based applications. If a fault is detected the unit with cut power immediately with a unique reset switch. High Amp circuit breaker manual reset. Sealed IP67 for engine...

Relaxn Fuse Blocks - Modular. Fuse box fits together providing the ability to expand. Accepts automotive fuses (ATP/ATC/ATO). 100A positive bus bar with M5 10mm studs. 0.250 quick terminals. Transparent cover with recessed area for label stickers...

Relaxn Buss Bar 12 Way - Modular Fuse box fits together providing the ability to expand. Accepts automotive fuses (ATP/ATC/ATO). 100A positive bus bar with M5 10mm studs. 0.250 quick terminals. Transparent cover with recessed area for label...

Needing to fill holes inside gauge clusters? An Instrument Blank is the ideal solution for covering up 52mm holes, left by gauges and other parts on your boat, simply push them into the hole and it’s done, no need for tools or fasteners...

CDI Electronics Tilt/Trim Relay - Yamaha - 857-1950. 40 amp for Trim/Tilt Replaces: 6G5-81950-01-00, 6F5-81950-01-00 Part Number CDI-857-1950

CDI Electronics Wiring Harness 2/4/6 Cyl. - Mercury, Mariner. 1970-1981 (20 & 40HP - 2 Cyl.) 1967- 1975 (50,65,80 & 85HP - 4 Cyl.) 1966-1979 (90,95,100,115,125,135,140 & 150HP - 6 Cyl.) Harness Exits Through the Side of the Lower...

CDI Electronics Tilt/Trim Relay 12 Volt, 40 amp. - Mercury, Mariner - 852-9809. 12 Volt, 40 amp for Trim/Tilt Replaces: 582472, 584416, 586224, 586147, 9-15200, 87-19761 Part Number CDI-852-9809

CDI Electronics Tilt/Trim Relay 12 Volt, 40 amp. - Mercury, Mariner - 852-9819. 12 Volt, 40 amp for Trim/Tilt Replaces: 882751A 1, 882751A 2, 828151, 828151A 1, 828151A 2 Part Number CDI-852-9819

Standard equipment on all Hydraulic Jackplates. Part Number BLA-201875

Standard equipment on all hydraulic Jackplates. Part Number BLA-201907

Traditional brass switch panels made from solid brass and available in 1, 2, 3 & 4 switch configurations. The panel is 2mm thick with either a polished finish or chrome plated. Single pole traditionally styled toggle switches are fitted...

Power Trim/Fuel Pump Relay manufactured by Sierra. Evinrude Replaces: 582472, 584416, 586224 5 Terminal Single Pull - Double Throw - 12 Volt Open Contact: 40 Amps Resistive 30 Amps Conductive Closed Contact: 20 Amps Resistive 15 Amps...

Duplex 1-4462 stainless steel propeller shaft. This shaft is machined with 1:10 taper and a keyway as standard. It is supplied with key and propeller nut with integrated zinc anode. The dimensions of taper and keyway are in accordance with ISO 4566...

There are two possibilities to water lubricate your shaft assembly; By means of a water scoop G 3/8, with ball valve, hose pillar, 1 metre of water hose and hose clamps, or By tapping a small amount of water from the main engine’s raw water...