Senders

TBS Communication Kit - RS232 Connection. TBS PC Communication Kit to Suit Enerdrive ePRO monitors, includes bundled software. Allows recording of all parameters including temperature (via...

Waste tank sender unit with a 1-1/4" BSP thread, 800mm long. 0-180 OHMS 316G stainless steel Rubber gasket and stainless steel screws included Part...

BEP Mon Sys DCSM Tank Probe Interface The 80‐600‐0029‐00 interface unit converts the point detection of the RV‐TSPK and 600-TGSK tank senders to the 0‐5VDC range used by the DCSM system monitor...

Blue Sea Vessel Systems Monitor Tank Sender - Diesel, Water, Waste Accurate - used with the Vessel Systems Monitor VSM 422 PN 1800—can be precisely calibrated for each tank* Reliable - SSI...

Blue Sea Vessel Systems Monitor Tank Sender - Gas Only Accurate - used with the Vessel Systems Monitor VSM 422 PN 1800—can be precisely calibrated for each tank* Reliable - SSI Technologies, Inc...

Vetus Sensor for Exhaust Temperature Alarm to fit Exhaust Hose Fits directly into the exhaust hose length, ideally just after the engine exhaust elbow fitting. Complete with sealing O...

Kus Tank Sender NMEA 2000 - NS3 Series Utilising magnetic field to control the reed on-off switch, the product features a long service life and protection against vibration. NOTE: The 'screw in'...

These Sensotex senders fit a 1-1/4" BSP thread and change resistance between 0-180 Ohms. Two lengths are available and a rubber gasket is included. Note that length is measured from the underside of...

Simarine Water Tank Pressure Sensor Enerdrive SI-TPS is from a series of High Performance compact pressure senders. These transmit by using a ASIC signal conditioning chip and dry ceramic capacitive...

BEP Tank Level Monitor Sender Interface Module The 600-TLM-SIF signal converter module is used to convert from 10-180 ohm, or 240-33 ohm tank sender outputs, to a 0-5V output. BEP equipment that...

Waste tank sender unit with a 1-1/4" BSP thread, 250mm long. American Standard 240-33 ohms (240 ohms at empty, 33 ohms at full) 316G stainless steel Rubber gasket and stainless steel screws...

Kus Waste Tank Level Sensor Kit with 200mm Sender This waste tank sender kit is used to detect the level of waste with in a vessels waste tank. Sender Length: 200mm This waste tank LED Gauge and...

Sender waste tank Matro toilet control switch points 170/60mm. Part Number SAW-453098

This sensor can be connected to a rudder angle gauge to show the angle of the rudder. Use the dual sensor when two gauges will be connected to one sensor, such as in a boat with two steering stations...

6 Hole Waste Senders - 240-30 OHMS. American Standard 240-33 ohms (240 ohms at empty, 33 ohms at full) 316G stainless steel. Rubber gasket and stainless steel screws included. Also includes a spout...

Veethree’s reed switch sender is compatible with a variety of fuel and fluid types, including; gasoline, diesel, hydraulic fluids, black water and grey water. The reed switch sender unit provides...

Veethree’s reed switch sender is compatible with a variety of fuel and fluid types, including; gasoline, diesel, hydraulic fluids, black water and grey water. The reed switch sender unit provides...

Enerdrive Standard Battery Watch Part Number ENE-EN-DCBW02

KUS senders fit a 1-1/4" BSP thread and change resistance between 240-33 Ohms. Multiple lengths are available and a rubber gasket is included. American Standard 240-33 ohms (240 ohms at empty, 33...

Sender Resistance Exchanger for Gauges This resistance exchanger allows 0-190 ohm senders to be used with 240-33 ohm gauges. It also allows 240-33 ohm senders to be used with 0-190 ohm gauges. Use...