Senders

KUS senders fit a 1-1/4" BSP thread and change resistance between 240-33 Ohms. Multiple lengths are available and a rubber gasket is included. American Standard 240-33 ohms (240 ohms at empty, 33 ohms at full) Suitable for fuel - petrol, ethanol...

Sender Resistance Exchanger for Gauges This resistance exchanger allows 0-190 ohm senders to be used with 240-33 ohm gauges. It also allows 240-33 ohm senders to be used with 0-190 ohm gauges. Use this device to adjust the top and bottom points of the...

Simarine Tank Sender 1-1/4" BSP 240-33OHMS Part...

Utilising a magnetic field to control the reed on-off switch, the sender features a long service life and protection against vibration. Compatible with Fuel Gauges with a 240-33 Ohms resistance. American Standard 240-33 ohms (240 ohms at empty, 33 ohms...

Kus Sender Alarm Module Sab High/Low. Allows the user to add a high and low level alarm signal to the control and monitoring system. The high/low level alarm position could be adjusted by turning the two adjusting knobs. Used with sending units with...

The Enerdrive fuel & liquid gauge sender is designed to work with gauges using the 240-33Ohm resistance system. The sender uses a magnetic reed switch, which guarantees a steady output signal. The small number of moving parts, and the solid...

This KUS Pressure Sensor Bar Switch combines the advantages of excellent anti-vibration performance and has a long service life with a waterproof rating of IP66. Part NumberVoltageOutputAlarmThread SAW-40023 6v - 24v 0 - 10 Bar 0.5±0.2...

This KUS Pressure Sensor combines the advantages of excellent anti-vibration performance and has a long service life with a waterproof rating of IP66. Part NumberBarVoltageOutputThread SAW-40020 0 - 5 6v - 24v 10-184 Ohm 1/8"...

 High Quality Long Service Life Pressure Sensor. Excellent anti-vibration performance. Operating Voltage: 6V~24V. Operating temperature: -25 ~120°C (120°C MAX 1H). Protection Rating: IP66. Part NumberMeasuring...

Stainless steel topside/underside adapter kit for tanks to suit 1-/4 BSP senders. The six holes are tapped to suit the screws provided. Rubber gasket and stainless steel screws included. This fitting has a top plate and a bottom plate (horse shoe...

Manufactured by KUS, this range of oil temperature sender units are compatible with most brands of temperature gauges. Available with a range of threads to suit different housings, these brass temperature sensors will operate up to a maximum of 150°...

Manufactured by KUS, this range of water temperature sender units are compatible with most brands of temperature gauges. Available with a range of threads to suit different housings, these brass temperature sensors will operate up to a maximum of...

Alloy weld-on or screw-in adapter for tanks with 5 holes tapped with a metric thread. The holes do not go all the way through. This sender adapter converts tanks with 5-hole fittings for 1-1/4" BSP senders. Part Number Internal Hole Width Overall...

Alloy Weld In Sender Flange - 1-1/4" BSP Thread T6063 Alloy Note: Special sizes available to order. Length is measured from underside of the flange to the base of the shaft. Part NumberPack Size SAW-40129 Single SAW-40129-20 20...

Sender unit adapter made from stainless steel. This weld-in bush suits 1-1/4" BSP thread senders. Outside Diameter: 56mm

Simarine Temperature Sensor Cables TC Thermistor accuracy temperature sensor 5K 1% 3950 Waterproof Probe Part NumberLength SIM-SI-TS01 1m SIM-SI-TS02 5m

Stainless Steel Fit Kit 6 Hole suits Waste Sender Rubber gasket and stainless steel screws included. PART NO. 40130 Note: Sensotex Replacement Nylon fixing kit Part numberDescriptionN/AN/A SAW-40130 Stainless Steel Fit Kit 6 Hole suits Waste...

Needing to fill holes inside gauge clusters? An Instrument Blank is the ideal solution for covering up 52mm holes, left by gauges and other parts on your boat, simply push them into the hole and it’s done, no need for tools or fasteners. Available...

This nylon adapter fits in the holes used by a 5 hole sender and allows a 1-1/4" BSP screw-in sender to be used. It can also be added to a hole to allow a sender to be fitted.

Sender Gasket Nitrile - Suits Standard 5 Hole Pattern Part Number Mount Style Mount Flange Diameter SAW-40124 5 Hole 69mm