Senders

Simarine Water Tank Pressure Sensor Enerdrive SI-TPS is from a series of High Performance compact pressure senders. These transmit by using a ASIC signal conditioning chip and dry ceramic capacitive pressure sensor. it has features of anti-corrosion,...

Kus Tank Sender NMEA 2000 - NS3 Series Utilising magnetic field to control the reed on-off switch, the product features a long service life and protection against vibration. NOTE: The 'screw in' senders are often purchased with SAW-40128 tank adapter...

Vessel Systems Monitor Tank Sender - Diesel, Water, Waste Three intuitive display modes Flexible case design offers three mounting options Fully programmable legends and adjustable alarm functions can be customized to fit every boat Monitors DC...

Vessel Systems Monitor Tank Sender - Gas Only Accurate - used with the Vessel Systems Monitor (BS-1810B) - can be precisely calibrated for each tank Reliable - SSI Technologies, Inc. Fluid-Trac is non-contacting eliminating any mechanical moving...

TBS Communication Kit - RS232 Connection. TBS PC Communication Kit to Suit Enerdrive ePRO monitors, includes bundled software. Allows recording of all parameters including temperature (via additional temp sensor) - RS232 Connection Part...

Enerdrive Standard Battery Watch Part Number ENE-EN-DCBW02

The Enerdrive fuel & liquid gauge sender is designed to work with gauges using the 240-33Ohm resistance system. The sender uses a magnetic reed switch, which guarantees a steady output signal. The small number of moving parts, and the solid...

Simarine Tank Sender 1-1/4" BSP 240-33OHMS Part...

Simarine Temperature Sensor Cables Part Number Length SIM-SI-TS01 1m SIM-SI-TS02 5m

Kus Sender Alarm Module Sab High/Low. Allows the user to add a high and low level alarm signal to the control and monitoring system. The high/low level alarm position could be adjusted by turning the two adjusting knobs. Used with sending units with...

Needing to fill holes inside gauge clusters? An Instrument Blank is the ideal solution for covering up 52mm holes, left by gauges and other parts on your boat, simply push them into the hole and it’s done, no need for tools or fasteners. Available...

Matromarine 3 Buttons Control Panel is the latest in design and technology, equipped with a programmed microprocessor having 3 options:- LED indicator lights - On/Empty - 3/4 - Full Short Use: Ideal for reduced water consumption. Before Use:...

Kus Temp Sender Water - Brass Main Body. Rated voltage: 6V~24V. Temperature response time: Minimum 3 minutes after power supply electrified. Protection Rating: IP67. Part Number Thread Volts Alarm Temperature Max...

Kus Waste Tank Level Sensor Kit This waste tank sender kit is used to detect the level of waste with in a vessels waste tank. LED Low-High-Full indicator with on/off switch. Cable length 6m Part NumberPowerVoltsCut Out Diameter (A)Cut Out...

 High Quality Long Service Life Pressure Sensor. Excellent anti-vibration performance. Operating Voltage: 6V~24V. Operating temperature: -25 ~120°C (120°C MAX 1H). Protection Rating: IP66. Part NumberMeasuring...

Alloy Weld In Sender Flange - 1-1/4" BSP Thread Note: Special sizes available to order. Length is measured from underside of the flange to the base of the shaft. Part Number Pack...

KUS 5 Hole 304G Stainless Steel Senders - to suit NMEA 2000 network.  Utilising magnetic field to control the reed on-off switch, the product features a long service life and protection against vibration.  304G stainless steel.  SAE...

This KUS Pressure Sensor Bar Switch combines the advantages of excellent anti-vibration performance and has a long service life with a waterproof rating of IP66. Part NumberVoltageOutputAlarmThread SAW-40023 6v - 24v 0 - 10 Bar 0.5±0.2...

This KUS Pressure Sensor combines the advantages of excellent anti-vibration performance and has a long service life with a waterproof rating of IP66. Part NumberBarVoltageOutputThread SAW-40020 0 - 5 6v - 24v 10-184 Ohm 1/8"...

Waste tank sender unit with a 1-1/4" BSP thread, 800mm long. 0-180 OHMS 316G stainless steel Rubber gasket and stainless steel screws included Part numberLengthOhms SAW-42800 800mm 0-180

Manufactured by KUS, this range of water temperature sender units are compatible with most brands of temperature gauges. Available with a range of threads to suit different housings, these brass temperature sensors will operate up to a maximum of...

Waste tank sender unit with a 1-1/4" BSP thread, 250mm long. 240-30 OHMS 316G stainless steel Rubber gasket and stainless steel screws included Part numberLengthOhms SAW-42525 250mm 240-30

These Sensotex senders fit a 1-1/4" BSP thread and change resistance between 0-180 Ohms. Two lengths are available and a rubber gasket is included. Note that length is measured from the underside of the flange to the base of the shaft. Part...

KUS senders fit a 1-1/4" BSP thread and change resistance between 240-33 Ohms. Multiple lengths are available and a rubber gasket is included. Note that length is measured from the underside of the flange to the base of the shaft. Part...

This nylon adapter fits in the holes used by a 5 hole sender and allows a 1-1/4" BSP screw-in sender to be used. It can also be added to a hole to allow a sender to be fitted.

Alloy weld-on or screw-in adapter for tanks with 5 holes tapped with a metric thread. The holes do not go all the way through. This sender adapter converts tanks with 5-hole fittings for 1-1/4" BSP senders.

Sender unit adapter made from stainless steel. This weld-in bush suits 1-1/4" BSP thread senders.

Utilising a magnetic field to control the reed on-off switch, the sender features a long service life and protection against vibration. Compatible with Fuel Gauges with a 240-33 Ohms resistance. 5 SAE standard holes. 316G stainless steel main body...

This resistance exchanger allows 0-190 ohm senders to be used with 240-33 ohm gauges. It also allows 240-33 ohm senders to be used with 0-190 ohm gauges. The top and bottom points can be adjusted. Runs off both 12V and 24V. Part...

6 Hole Waste Senders - 240-30 OHMS. 316G stainless steel. Rubber gasket and stainless steel screws included. Also includes a spout for a hose wash connection. Part...

Stainless steel topside/underside adapter kit for tanks to suit 1-/4 BSP senders. The six holes are tapped to suit the screws provided. Rubber gasket and stainless steel screws included. This fitting has a top plate and a bottom plate (horse shoe...

Stainless Steel Fit Kit 6 Hole suits Waste Sender Rubber gasket and stainless steel screws included. PART NO. 40130 Note: Sensotex Replacement Nylon fixing kit Part numberDescriptionN/AN/A SAW-40130 Stainless Steel Fit Kit 6 Hole suits Waste...

This sensor can be connected to a rudder angle gauge to show the angle of the rudder. Use the dual sensor when two gauges will be connected to one sensor, such as in a boat with two steering stations. Part...