Networking and Adaptor Cables

Raymarine Volvo Engine Y-Loom cable Part Number RAY-E70241

Raymarine Yamaha Command-Link Cable Part NumberLength RAY-E70242 1m

Lowrance N2K-PWR-RD Network Power Nod The N2K PWR-RD is a NMEA 2000 Power Cable that comes with a NMEA 2000 network T connector. Part Number LOW-000-0119-75

Lowrance Fluid Level Sensor Part Number LOW-000-11518-001

Raymarine RayNet (F) to SThs (M) Socket Adaptor Cable The new Raynet (F) to SeaTalkhs (M) cable adapter allows you to fit the existing waterproof, locking SeaTalkhs cables used with G-Series, E-Wide, C-Wide and E-Classic* MFDs to new...

Connect your GPSMAP 8400 or 8600 series chartplotter to a J1939 network to gain access to features, such as engine or generator monitoring. Like the NMEA 2000 network, the J1939 network follows a standard and uses proprietary messages...

Power the GMR Fantom 5x/12x series radars with this 48 foot (15 meters) long 12 AWG cable. Note: When used with the 100 W Fantom series radar, a voltage converter is required. Part Number GMN-010-12067-10

  Raymarine Fistmic Adaptor Cable (12 pin to 8 pin) 400mm Part Number RAY-A80296

Quickly set up an Ethernet connection between two Humminbird Ethernet-capable units. Available in five lengths—you select the length you need. Part NumberLength HUM-103901 1.5m HUM-103902 3.0m HUM-103905 4...

B&G WS310 Wired Interface WS310 (wired) Interface for use with WS310 Wind Sensor, allows connection to your NMEA 2000® network. Part NumberSupply VoltageCompass SafeWarrantyW x H x D BAG-000-14389-001 12V DC 300mm 2 years 90mm x 20mm...

Humminbird Cable Adaptor for External GPS to suit APEX The AS GPS is an adapter cable that allows APEX chartplotters to connect with a Humminbird external GPS receiver. Combined with an external GPS receiver, users will get extremely accurate position...

Raymarine RayNet male to RJ45 adaptor cable. This has a RayNet Female connector at one end and a RJ45 Female Gland connector at the other end. The Gland makes the RJ45 Female socket watertight. A typical use for this cable would be to convert a...

The Raynet (F) to RJ45 Ethernet (M) adapter can be used to connect new a, c, e or gS-Series MFDs to the SR6 or 8-Port Seatalk High Speed network switch. When used in conjunction with a crossover coupler, this adapter can also convert the Ethernet...

The new Raynet (F) to SeaTalkhs (F) cable adapter allows you to fit the existing waterproof, locking SeaTalkhs cables used with G-Series, E-Wide, C-Wide and E-Classic* MFDs to new generation RayNet multifunction displays. *Note: The E-classic...

Raymarine RayNet (M) Pins to RayNet (M) Pins Cable Joiner. The new RayNet (M) to RayNet (M) Cable Joiner adapter lets you connect two standard RayNet networking cables together in instances where you need to extend the length of a cable run. ...

RayNet (M) Pins to SThs (M) Socket Adaptor Cable A typical use for this adaptor cable would be to convert the new "RayNet(F)" Digital Radar cable to the "SThs (M)" connector, so that it can be plugged directly into the back of a...

CZONE NMEA 2000 4-Way Tee Connector Connects multiple devices into the NMEA backbone Part Number CZO-CZ-80-911-0048-00

Garmin ECU Power Cable Provide power to your electronic control unit (ECU) with Garmin's ECU power cable. Simply wire the ECU power cable to your boat battery as one of the last connections made during GHP™ 10 installation. Part...

Garmin Quarter-turn Collar CCU Extension Cable - 15m Mount your CCU farther than 3m (9.8 feet) away from the ECU with a 15m (49.2 ft) extension cable. Part Number Length GMN-010-11156-01 15m (49.2ft)

Connect your compatible Garmin marine device to a HDMI device with this 15-foot cable. The water-resistant and secure connection supports full HD video and audio playback. Refer to your device owner’s manual for more information on supported A/V...