Plumbing, Sinks, Toilets & Pumps

Seaflo Replacement Head Kit for 42 Series Pumps Part Number For Pump Series SFL-SFHK-42 42

Economical manual bilge pump offering great value for money. This self priming pump will deliver approximately 35 litres of water per minute. Fixed handle with rubber hand grip. Inlet / outlet ports Suit 25mm (1") hose Part NumberLitres Per...

Shurflo Valve Pump Assembly - SP-221. T/S 2088 Series Part Number Number SAW-SP-221 3

PVC reinforced shower hose for boat decks. This shower hose is 2.5 metres in length and comes complete with connectors to suit 1/2" BSP Female hose fittings. Part numberTypeHose LengthConnections SAW-51060 Nylon Reinforced 2.0m 1/2" BSP...

Nylon reinforced shower hose for boat decks. This shower hose is 2.0 metres in length and comes complete with connectors to suit 15mm Male and 3/8" BSP Female hose fittings. Suits the following products: Shower Flick Mixer & Pullout Shower...

Surge Damper manufactured by Whale. Prevents water hammer and also reduces switch hunting. Designed for pressurised systems using the Whale quick connect systems. The surge damper should be mount in a vertical position immediately after the...

A high quality membrane pump suitable for pumping/ transferring bilge water, seawater or diesel.  Suitable for boats up to 12m (ISO 15083) Synthetic housing, metallic parts of stainless steel (AISI 316) Easy to remove clamping ring for...

A modern styled moulded panel switch which incorporates a bilge pump control and alarm. A red alarm light and an audible alarm sounds if a bilge pump fails on automatic and the water rises to the level of the 2nd float switch. Includes fuse holder with...

Vetus Cooling Water Hose for Cooling Water (per metre) Type MWHOSE is made of EPDM rubber with synthetic fabric and spiralled steel reinforcement. The hose is suitable for cooling water, both suction and pressure (max. 2.5 bar), salt and fresh...

Covered Drain manufactured by Marine Town. These covered drains combine smart aesthetics with easy single hole installation for anchor wells, motor wells and similar. Rounded no catch, cast and highly polished 316 grade stainless steel head...

SHURflo bilge pumps are fully submersible with anti-airlock protection. Stainless steel shaft. Tough nylon impeller and baseplate construction. Transom mount with 0.9m (3ft) tinned wire for easy installation. CE Certified, Ignition Protected ISO...

Tuckaway Faucet manufactured by Whale. Simple and lightweight Whale® faucets. Easy to install and available with an optional on/off valve. For use with Whale® foot or non-pressurised electric pumps. Moulded acetal and anodised...

This 316 Stainless Steel thru-hull with strainer is suitable for raw water intake for a gen-set or live bait tank. The 1" threaded tail will allow mounting to hulls up to 3/4" thickness. Accepts a 3/4" ID pipe. Part numberSuits Hose SAW-45068 20mm...

Seaflo Replacement Head Kit for 22 Series Pump Part Number For Pump Series SFL-SFHK-22 22

TMC Livewell Motor Cartridge Suits SAW-23023 / SAW-23024 / SAW-23025 Part Number SAW-23026

CAN-SB Universal Hose Connector 13mm - 38mm Can be trimmed to join hoses ranging 13mm to 38mm. Designed to make hose reduction easy. Size: 13mm - 38mm Part numberDescriptionSizeN/A SAW-45358 CAN-SB Universal Hose Connector 13mm - 38mm 13mm - 38mm -

Covered Drain manufactured by Marine Town. These covered drains combine smart aesthetics with easy single hole installation for anchor wells, motor wells and similar. Rounded no catch, cast and highly polished 316 grade stainless steel head...

TMC Contact Bilge Pump - 900 GPH. Fully submersible bilge pump. Permanent magnet motor. Compact design. Corrosion resistant plastic housing. Tough nylon impeller construction. Snap-off base for easy mounting or cleaning. Transom mount with 0.9m...

Combine with bilge pump for automatic operation. Float switch is made of high impact plastic, ultrasonically welded together with easy to remove shield. Non-mercury mechanical switch. Clear plastic shield makes it easy to see if debris is blocking...

A quality multi-size non-return valve for use with manual bilge pumps. Prevents back flow of water into the bilge. The valve should be mounted as close as possible to the inlet strainer. Suitable for both 25mm (1”) and 38mm (1 1/2”) hose...